Thomas & Thomas

Blog Comments

  1. tomfly's Avatar

    I worked on the handle a bit. It is still not finished. I am going about it slow. I have been reading up on cutting ebony. There is a slight problem with the wood. It is prone to cracking. What causes the problem is heat. So I am doing it in gradual increments. I can not work the wood more then 5 minuets at a time and then 20 minuets to cool. Hope to have it finished by next week end.
  2. tomfly's Avatar

    I received all my guides for the rod on Saturday. I royal F*** that up! Every guide that I ordered including the stripper guide is 1 size to large. The two tips were correct. I will have to some reordering. I started turning the ebony last evening (what did I get myself into) It took about an hour to find the center of both ends and drill the holes in each end. It took another hour to knock off the square corners with a plane. Then I was able to start turning it. It took an hour and a half to remove a quarter of an inch off the stock. It is like turning a piece of granite. And this is the best part the motor on the lathe went poof in a puff of smoke (what the f####). I had to think, I did not want to rebuild the drive assembly. What I came up with; is I remove the shaft that turns within the armature assembly and the bearing assembly from the motor. I mounted a router to the back of the drive mount on the lathe. I mounted the bearing assembly to the front of the drive mount on the lathe. The old motor shaft is attached between the router and the bearing assembly. It works well. I dodged a bullet. I will try to continue turning tomorrow evening.
    Updated 11-08-2011 at 09:54 PM by tomfly
  3. golden beetle's Avatar

    This is a great blog.

    Good luck with the rod!
  4. tomfly's Avatar
    Success at last; I turned my first test handle this evening that did not come out looking like a piece of crap. I am mildly pleased.
    after 3 horrific failed test handles. I think I am getting it down. This is the design that I came up with. What is holding me back now I do not have the Slide Ring and Pocketed but cap, I ordered it 2 weeks ago and I still do not have it. I can not proceed with out knowing what diameter of the reel seat but I am confident I can turn the handle with success..

    handle2.jpg picture by tomfly1 - Photobucket
    Updated 11-04-2011 at 04:19 PM by tomfly
  5. tomfly's Avatar

    I am having some trouble with drilling a whole 10 1/2” long. Drilling the whole is not the problem. The issue I am having is Drilling a perfectly straight hole that is 10 1/2” long. I tried it free hand nada… I tried in a Drill press nada….. I do not think it can be done. From what I have been reading Wood is one of the hardest substances to drill accurately. The trouble is that wood does not have a consistent density, so the drill bit follows the laws of physics and takes the path of least resistance hence creating a crooked whole. I came up with a new solution. What I have decided to do is drill 4-5 inch whole in the handle and cut the Rod.
  6. tomfly's Avatar
    Finished construction of the lathe last evening, started to practice turning. I suck at it. Need a lot of practice. I am happy with the way the lathe operates. But it scares the crap out of me. I do not trust it yet (I guess I have home made lathe syndrome) I am surprised it works at all. It is the first time I have ever done anything like this. Just made from some stuff I had lying around and some hardware (Nuts bolts threaded rod). Total cost was about $25. The biggest challenge that I encountered is drilling a 10 1/2" whole straight through the center of the stock. Not an easy task. I ordered all the components need to continue with the rod build. ( guides, thread, .) This better come out the way I want it too. I gave up all my Fall fishing for this rod.
    Updated 10-28-2011 at 06:47 PM by tomfly
  7. tomfly's Avatar

    It has been a hectic week at my home. Had windows replaced. Then had the interior painted. I still made some process on the rod. On my 9th coat of Tung oil I sanded with 600 grit after the 3rd and 6th coats. I then realized that I can achieve the desired finish if I wipe on the Tung oil and immediately wipe it off. I believe the first few coats I wiped on were too heavy it gave the rod an uneven finish. Now the rod is maintaining a very smooth finish. I have been working evenings on the build of the wood lathe inspite of all the activity in my house. I have the drive assembly fully working. I have assembled the tool rest. The only assembly that remains is the tail stock. I should be turning some practice handles by the end of the week. I decided to keep putting coats of Tung oil on the rod until the handle is turned.
  8. tomfly's Avatar
    10- 18-11

    I have made some more progress. I have put the third coat of Tung Oil (another one of Ronbo’s suggestions) on the rod this morning. It is starting to have a nice shine to it. I have most of the wood lathe complete. Work on a good chunk of it last night. It is amazing what you can build with some plywood, an old steal bed frame, shop-vac motor and the track from my old shower door assembly. I have ordered my Buttcap, Slide ring and the winding check (I hope measured it right.) Hopefully by the weekend I can start to practice turning a handle. I still need to order guides and thread. I have not decided on what I want to use at this point. I got to hand it to you guys who build rods. I am just redoing a rod and it is a lot of tedious work.
  9. tomfly's Avatar
    Haven’t posted to my blog for a while There were some site problems and I went on vacation with my wife. I have made some progress though.

    I stripped the old finish of the rod last week. I took Ronbo’s suggestion and used Citristrip. I had to apply it twice in 30 minuet intervals. It worked great thanks Ron. I used a small putty knife to remove the stripping agent and old varnish. I cleaned the rod with odorless mineral spirits. I had to do this numerous times. A brown film kept coming off the rod. After 8 to 10 times of wiping, I could wipe the rod and the rag would be clean.
    I was able to polish the ferrules with Bar Keepers Friend.( I did this before I removed the finish, I did not want to get any polishing compound on the raw bamboo.) They shined up very nicely. I wasn’t sure how they were going to come out but they look great. The person who built the rod originally dresses the ferrules beautifully, they are very nicely tapered into the rod, probably why they haven’t cracked or checked. I have decided not to replace them.
    I do not have a heat gun to straighten the sections with. I am going to try a hair dryer that I stole from my wife. I will let you all know if it works. After I get it straight I can start the finishing process.

    ROD6.jpg picture by tomfly1 - Photobucket

    Rod4-1.jpg picture by tomfly1 - Photobucket

    rod3.jpg picture by tomfly1 - Photobucket

    I received my rod grip yesterday. A piece of Gabon Ebony It is not much to look at now. After I turn it should be nice. I am going to attempt to build a home made wood lathe. I have most of what I need laying around the basement, attic and shed. I haven’t turned a piece of wood since eight grade wood shop. I will have to practice a bit before I attempt to cut the Ebony. Will start building my rod wrapper today, I have drawn up some plans so it should not take to much time.

    Rod5.jpg picture by tomfly1 - Photobucket

    I have made some progress on my thread wrapper it is almost finished. Have most of the components together for the construction of the wood lathe. The hardest part was obtaining a working electric motor. I removed an old AC fan motor it burned up while testing it. I had to revert to plan B. I scavenged a motor out of an old shop vac. It works great. It spins a little to fast. I will reduce the RPM with pulleys and a belt.
    Updated 10-14-2011 at 08:40 PM by tomfly
  10. tomfly's Avatar
    Day 3 10-5-11

    I finished removing the old wrap off the rod this evening. I found an easier way to accomplish this. I used an X-Acto knife to grab a single thread. I could unwind the wrapping without cutting the thread off. A much more efficient way. I went to the store to pick up some hardware for the construction of a rod wrapper. I will probably start building it this weekend. Planning on stripping off the finish tomorrow evening.
    Updated 03-25-2012 at 02:28 PM by tomfly
  11. tomfly's Avatar
    Day 2 10-4 -11
    I spent a few hours on the rod last night. I took detailed measurements of the rod that included the center point of all the guides. I removed the reel seat. It was very simple, as it was held on with a small screw. There is a small piece of wood glued to the rod that was under the reel seat. I will see if I need to remove that after I receive the new seat. I cut away the old cork grip. I was worried about scoring the rod. The way I went about this is to cut halfway through the cork and chip it with a small screw driver. The cork came off very easy. The epoxy that held it on was a different story. I slowly cut it away with a razor knife. I have it close to the bamboo, if the stripping agent does not remove the rest. I do not believe it will impede the new grip. I started removing the wrap. This can be tedious. I was incorrect in my initial assement there is no red thread on the rod. It is red nail polish. Not fun to remove. I will probably do some more tonight. I will post some pictures after I complete this.
    Updated 05-13-2012 at 09:44 AM by tomfly
  12. Ronbo's Avatar
    I use Citristrip gel and have done a number off old rods with it.
    Follow the directions and the old varnish will wipe right off.
    follow with their stripper after wash and the rod will be clean.
    I have not had any glue issue arrive from using the stripping solution.
    The razor technec is a little more dangerous and you could wind up damage
    especial on the corners of the rod. I then sand with a 400 grit sand paper and final buff with 0000 steel wool.
    I put two coats of a wipe on Tung oil finish buff out with a soft cloth and the rod is ready to wrap
    Hope this helps
  13. tomfly's Avatar
    Rod repair Day 1 10-2-11

    Rod Assessment:

    I had a chance to review the overall condition ot the rod today.
    The rod was filthy. I cleaned it with a brush and mild detergent. From the appearance and the ammount of gunk in the guides, I do not believe that the rod has been fished with in long time. I had to put a real on it and try it . I was supprised how well and accurate it casts a six weight line. I was able to cast the whole line without much effort.

    The rod has three diffrent type of wraps on it. It has the orignal gold, it appears to have some fragility issues probably dry rot. This would explaine the atroshishy done red and black wraps on the guides.

    The finish on the rod is chipped and pitted. The finish needs to be striped and re-dipped. I have concern on what cource to take stripping of the bamboo. From what I read there are two schools on this procudure. Using a stripping agent or scraping it with a razor blade. I need to make a discissionon how I am going to attack this problem. (any suggestions would be helpful)

    The bamboo is in relatively good condition, there are no splits, cracks or diviots. The butt section is straight. The mid section has a slight bow in it . One tip has a slight S curve in it. The second tip has a slight bow in it . I should know more after the guides are removed and I can roll them on a flat surface. Overall I am confident I can bring them back to straight and true.

    The cork handle has some issues. There is a section with a thumb size piece missing. There are some smaller gouges in it also. It will need to be repaced. The real seat has some ware, but it held the real just fine. Because I am going to replace the grip, I will change the real seat also, There no cracks in the ferrules but I want to upgrade them from aluminum to nickel.
    Updated 10-05-2011 at 07:18 PM by tomfly
Page 2 of 2 FirstFirst 1 2
  • New Forum Posts